Useful Tips

How do I reset my parrot MKi9100?

Contents

How do I reset my parrot MKi9100?

How to reset a Parrot MKi9100

  1. Turn on the MKi9100.
  2. Press the centre button on the remote and rotate until you get to “Settings”
  3. Enter Settings menu and navigate down to “Advanced Settings”
  4. When in Advanced Settings menu select “Factory Reset” and press the centre button on the remote.
  5. The MKi9100 will now re-boot.

How do I connect my parrot MKi9100?

Use the USB, Jack or iPod connectors to connect the Parrot MKi9100 to your audio player / iPod / USB stick. Press the button to launch the music function. Press the jog wheel to access the content of the selected source.

What is Parrot MKi9100?

The Parrot MKi9100 is a Bluetooth hands-free system with an OLED screen. A wireless remote control can be positioned on the steering wheel or dashboard and allows the driver to control all the functions of the MKi9100.

How do I turn my parrot off?

To do this, open ZIK 3 app and select Settings > Automatic Shut Off. This option is deactivated by default. So that your Parrot Zik 3 can switch off automatically, it must not be charging or in use.

How do I clear the memory on my parrot?

You can pair up to 10 devices with Parrot MKi9100. If you pair an eleventh phone, the hands-free kit will say “memory full”. You will then have to erase the memory by holding down the and buttons at the same for three seconds. This deletes all the synced contacts from the hands-free kit.

How do I reset my parrot?

How to reset a Parrot MKi9000

  1. Turn on the MKi9000 and wait about 20 seconds for the kit to fully turn on.
  2. Press the centre button on the remote and rotate until you get to “Settings”.
  3. Press and hold the RED and GREEN buttons on the remote control for 2 to 3 seconds.

How do Parrot hands free work?

Parrot MK6000:

  1. Start the car and ensure the car kit is on.
  2. Activate Bluetooth on your phone, and search for Bluetooth devices.
  3. Select MK6000 from the list.
  4. Enter 0000 on your phone when prompted.
  5. The Parrot MK6000 says “Pairing successful” when both devices are paired and will sound a beep when connected to your phone.

How do I update my parrot MKi9100?

On the MKi9100 go into Settings / Advanced / Firmware Update and press centre button to confirm. Within a minute you should see “update in progress” on the MKi9100 screen. After a minute or two the screen will go blank and this is when the unit is being re-programmed.

How do I remove devices from Parrot MKi9100?

1. Press the jog wheel and select Settings > Bluetooth > Paired devices. 2. Select the phone you want to disconnect from the kit.

Where is the mute button on Parrot mki9200?

Join the vehicle\[s audio and power supply cables to the female connectors of the Parrot MKi9200. 3. On the installation cable, connect the free yellow wire to one of the audio system\[s corresponding mute-in jacks if available (mute in 1, mute in 2 or mute in 3).

How to displa Yed on Parrot mki9200?

 To perform the installation check, turn the ignition on then off once the Parrot MKi9200 is installed: the message Goodbye! must be displa yed.  If it is not the case, it is necessary to inverse the positions of the red and orange wires.

How to install a remote control on a parrot?

Parrot MKi9200 – User guide 10 Installing the remote control on the dashboard If you want to place the remote control on the dashboard, stick the double-sided tape located on the flat side of the bracket to fix it against the dashboard. You can then insert the remote onto the bracket.

Where can I find a parrot Bluetooth car?

The Parrot Bluetooth Car Kit with Streaming Music features an OLED screen and a wireless remote control that can be positioned on the steering wheel or dashboard.